1W415-0299 / C / 03.12.03INSTALLER: THESE INSTRUCTIONS MUST BE CONVEYED TO AND REMAIN WITH THE HOMEOWNER.Wolf Steel Ltd., 24 Napoleon Rd., Barrie, ON
10W415-0299 / C / 03.12.03REQUIREDVERTICALRISE IN FEET(VT)CALCULATED HORIZONTAL VENT RUNPLUS OFFSETS IN FEET (HT)FIGURE 545ºFIGURE 690°H1H2when (HT) &
11W415-0299 / C / 03.12.03See graph to determine the re-quired vertical rise VT for the requiredhorizontal run HT.For vent configurations requiring mo
12W415-0299 / C / 03.12.03Example 3:V1=5 ftV2= 10 ftVT=V1 + V2 = 5 + 10 = 15 ftH1=3 ftH2= 2.5 ftHR= H1 + H2 = 3 + 2.5 = 5.5 ftHO= .03(one 45º elbow +
13W415-0299 / C / 03.12.03For vent configurations requiring more than one 45º andone 90° elbow , the following formulas apply:Formula 1: HT < 3VTF
14W415-0299 / C / 03.12.03When finishing the fireplace, combustible material mayrest directly on of the top extension. In order to achieve acountertop
15W415-0299 / C / 03.12.03Combustible materials may be installed flush with the frontof the fireplace but must not cover any of the black face-areas o
16W415-0299 / C / 03.12.03Refer to pages 6-13. All venting must have a minimumclearance of 1" to combustible.See Page 18 for additional framing d
17W415-0299 / C / 03.12.03Refer to pages 6-13. All venting must have a minimumclearance of 1" to combustible.See Page 18 for additional framing d
18W415-0299 / C / 03.12.03There must be a minimum of 1" clearance to combustibleswhen framing around all venting options. See pages 14-17.FIGURE
19W415-0299 / C / 03.12.03For optimum performance it is recommended that allhorizontal runs have a minimum 1 inch rise per foot us-ing flexible ventin
2W415-0299 / C / 03.12.03Pg 3-5 INTRODUCTIONWarrantyGeneral InstructionsGeneral InformationCare of Glass & Plated PartsDimensions 6-13 VENTINGVent
20W415-0299 / C / 03.12.03For safe and proper operation of the fireplace, followthe venting instructions exactly.1. Stretch the 5" diameter alum
21W415-0299 / C / 03.12.03FIGURE 40FIGURE 391. Move the fireplace into position.2. Fasten the roof support to the roof using the screwsprovided. The
22W415-0299 / C / 03.12.03Do not connect either the wall switch, thermostat orgas valve to electricity (110 volts).Attach the two leads to terminals
23W415-0299 / C / 03.12.03PHAZERTM logs, glowing and charcoal embers, exclusiveto Napoleon fireplaces, provide a unique and realistic glow-ing effect
24W415-0299 / C / 03.12.03FIGURE 50Attach the hood with louvre brackets by pressing the topflange of the bracket into the clips along the top of thel
25W415-0299 / C / 03.12.03Ensure that thedoor is properlyclipped onto thesteel lip to pre-vent overheat-ing, glass break-age and / or dis-colouration
26W415-0299 / C / 03.12.03Remove the "Z" shapedmounting bracket securedto the burner, by the pilot.Remove the thermodiscfrom the bracket su
27W415-0299 / C / 03.12.03• Turn off all gas to the fireplace.• Open windows.• Do not try to light any appliance.• Do not touch any electric switch; d
28W415-0299 / C / 03.12.03Adjust the pilot screw to provide properly sized flame. Turnin a clockwise direction to reduce the gas flow.Natural gas mode
29W415-0299 / C / 03.12.03# PART No. DESCRIPTION1* W361-0016 GLOWING EMBERS2* W550-0001 CHARCOAL EMBERS3 W562-0009 DOOR GASKET (100 INCHES)4 W010-0454
3W415-0299 / C / 03.12.03NAPOLEON gas fireplaces are manufactured under the strict Standard of the world recognizedISO 9001 : 2000 Quality Assurance C
30W415-0299 / C / 03.12.03* WARNING: This is a fast acting thermocouple. It is an integral safety component.Replace only with a fast acting thermocoup
31W415-0299 / C / 03.12.03# PART No. DESCRIPTION1 W690-0001 MILLIVOLT THERMOSTAT2 GD501 HEAT GUARD3* W573-0008 HI-TEMP SEALANT4* W010-0370 WALL SUPPOR
32W415-0299 / C / 03.12.03Carbon is beingdeposited onglass, logs orcombustionchamber sur-faces.Flame is impinging on thelogs or combustion cham-ber.-
33W415-0299 / C / 03.12.03Main burner goesout; pilot goes out.Refer to "MAIN BURNER GOES OUT; PILOT STAYS ON"Vent is blocked- check for ven
34W415-0299 / C / 03.12.03Wolf Steel Fireplace Service HistoryThis fireplace must be serviced annually depending on usage.DateService Technician NameS
35W415-0299 / C / 03.12.03NO TES
36W415-0299 / C / 03.12.03NO TES
4W415-0299 / C / 03.12.03THIS GAS FIREPLACE SHOULD BE INSTALLED ANDSERVICED BY A QUALIFIED INSTALLER to conform withlocal codes. Installation practic
5W415-0299 / C / 03.12.03Vent lengths that pass through unheated spaces (at-tics, garages, crawl spaces) should be insulatedwith the insulation wrappe
6W415-0299 / C / 03.12.03Use only Wolf Steel or Simpson Dura-Vent Model DV-GSventing components. Minimum and maximum vent lengths,for both horizontal
7W415-0299 / C / 03.12.03AIR TERMINAL INSTALLATIONS*** Recommended to prevent condensation on windows and thermal breakage********** It is r
8W415-0299 / C / 03.12.03VENTING APPLICATION FLOWCHARTVERVERVERVERVERTICALTICALTICALTICALTICALTERMINTERMINTERMINTERMINTERMINAAAAATIONTIONTIONTIONTIONH
9W415-0299 / C / 03.12.03Use the GD401 periscope kit to locate the air terminationabove grade. The periscope must be installed so that whenfinal gradi
Comments to this Manuals