1W415-0547 / C / 07.25.06W415-0547 / C / 07.25.06
10W415-0547 / C / 07.25.06USE GD201 PERISCOPE KITBELOW GRADE INSTALLATIONMAXIMUM 10FT VENT LENGTHOF HORIZONTALREGARDLESSVENT LENGTH24" MINIMUM12&
11W415-0547 / C / 07.25.06ELBOW VENT LENGTH VALUESDEFINITIONSHORIZONTAL TERMINATION02.5 5 7.5 10 12.5 154010203017.5 2039REQUIREDVERTICAL RISE IN FEET
12W415-0547 / C / 07.25.06V1HORIZONTAL TERMINATION20100 5 10 159010012011030405060708013014015020See graph to determine the required vertical rise VT
13W415-0547 / C / 07.25.06VERTICAL TERMINATIONExample 3:V1 = 5 ftV2 = 10 ftVT = V1 + V2 = 5 + 10 = 15 ftH1 = 3 ft H2 = 2.5 ftHR = H1 + H2 = 3 + 2.
14W415-0547 / C / 07.25.06H1VERTICAL TERMINATION0510152010203253019Formula 1: HT < 3VTFormula 2: HT + VT < 40 feetExample 4:V1 = 1 ftwhen (HT)
15W415-0547 / C / 07.25.06VERTICAL THROUGH EXISTING CHIMNEYThis appliance is designed to be attached to a 3" co-lin-ear aluminum fl ex vent system
16W415-0547 / C / 07.25.06This application occurs when venting through an exterior wall. Having determined the air terminal location, cut and frame a
17W415-0547 / C / 07.25.06 1. Fasten the roof support to the roof using the screws provided. The roof support is optional. In this case the venting is
18W415-0547 / C / 07.25.06 1. Attach the adjustable pipe to the last section of rigid pip-ing. Secure with screws and seal.2. Install the 4" alum
19W415-0547 / C / 07.25.06FINISHINGGLASS DOOR INSTALLATIONAND REMOVALCAST FRONT INSTALLATIONAND REMOVALFRONTSCREWSBRACKET32Follow the above steps in r
2W415-0547 / C / 07.25.06WHAT TO DO IF YOU SMELL GASDo not touch any electrical switch.If you cannot reach your gas supplier,call the fire department.
20W415-0547 / C / 07.25.06LOG PLACEMENTLOGO PLACEMENTLOGO1.27cm1.27cmRemove the backing from the the logo and position onto the control door as shown.
21W415-0547 / C / 07.25.06OPTIONAL SWITCH / WIRING DIAGRAMThe on/off switch is located on the back of the GDS25 at the top right corner. For ease of
22W415-0547 / C / 07.25.061. STOP! READ THE ABOVE SAFETY INFORMATION ON THIS LABEL.2. TURN REMOTE WALL SWITCH TO OFF POSITION.3. TURN OFF ALL ELE
23W415-0547 / C / 07.25.06NOTE: Check and adjust, if necessary, the primary air to 7/16” for propane and 1/4” for natural gas. Replace the screws.7.
24W415-0547 / C / 07.25.06Contact your dealer for questions concerning prices and availability of replacement parts. Normally all parts can be ordered
25W415-0547 / C / 07.25.06* WARNING: This is a fast acting thermocouple. It is an integral safety component. Replace only with a fast acting thermocou
26W415-0547 / C / 07.25.06Pilot will not light.Verify the "S" wire for the sensor and the "I" wire for the ignitor are connected t
27W415-0547 / C / 07.25.06Flames are very ag-gressive.- Venting action is too great.Tighten door clampsRestrict vent exit with restrictor plate. See R
28W415-0547 / C / 07.25.06Fireplace Service HistoryThis fireplace must be serviced annually depending on usageDATEDEALER NAMESERVICE TECHNICIAN NAMESE
3W415-0547 / C / 07.25.06WARNING• The stove is a vented gas-fi red heater. Do not burn wood or other materials in this stove.• Adults and especially
4W415-0547 / C / 07.25.06NAPOLEON products are manufactured under the strict Standard of the world recognized ISO 9001 : 2000 Quality Assurance Certifi
5W415-0547 / C / 07.25.06The blower power cord must be connected into a properly grounded receptacle. The grounding prong must not be removed from the
6W415-0547 / C / 07.25.06MAINTAIN THESE MINIMUM CLEARANCES TO COMBUSTIBLES:A. 4" B. 2"* C. 2" STOVE SHOULD NOT BE INSTALLED DIRECTLY
7W415-0547 / C / 07.25.06BLOWER INSTALLATION4582319774Blower (SEE LOCATION AND CLEARANCES)1. Cut and remove the tie securing the blower switch wires t
8W415-0547 / C / 07.25.06***** Recommended to prevent condensation on windows and thermal breakage********** It is recommended to use a heat shield an
9W415-0547 / C / 07.25.06Use only Wolf Steel, Simpson Dura-Vent, Selkirk Direct Temp or American Metal Amerivent venting components.For Simpson Dura-V
Comments to this Manuals