1W415-0614 / A / 07.24.07INSTALLATION ANDOPERATION INSTRUCTIONSWolf Steel Ltd., 24 Napoleon Rd., Barrie, ON L4M 4Y8 Canada • (705)721-1212 • fax(705)7
10W415-0614 / A / 07.24.07This application occurs when venting through an exterior wall. Having determined the air terminal loca-tion, cut and frame a
11W415-0614 / A / 07.24.077. Using the 10” diameter fl exible aluminium liner, apply sealant, slide a minimum of 2” over the fi replace combustion air c
12W415-0614 / A / 07.24.07Proceed once the vent installation is complete.Note : All gas connections must be contained within the fireplace when comple
13W415-0614 / A / 07.24.07WARNINGFacing and/or fi nishing material must never overhang into the fi replace opening.59 1/4"1"MIN1"MIN29&qu
14W415-0614 / A / 07.24.07FIGURE 30MANTLE CLEARANCES034 78912 567HEIGHTMANTLEMANTLE WIDTH5643Combustible mantle clearance can vary according to the ma
15W415-0614 / A / 07.24.07 1. Place the door frame face down careful not to scratch the paint. 2. Center the gasketed glass inside the door frame
16W415-0614 / A / 07.24.07NOTE: Refer to the FINISHING section of the BGD90NT/PT Installation Manual for instructions on removing the door and log sh
17W415-0614 / A / 07.24.076. Place the pin in log #7 in the hole in log #6. The log should sit in the notch on log #2 and the bottom should rest along
18W415-0614 / A / 07.24.07GLOWING EMBERSCHARCOAL EMBERSRandomly place the charcoal embers along the front and sides of the Hearth Panels in a realisti
19W415-0614 / A / 07.24.07RECEIVERSLOTSPARK MODULEVALVEWING NUT1. Remove access panel from inside the fi rebox.2. Unplug the control module from the ju
2W415-0614 / A / 07.24.07 PG2-5 INTRODUCTION Warnings and Safety Precautions Warranty Dimensions General Instructions General Information
20W415-0614 / A / 07.24.07To operate this fi replace using the remote, the pilot must be running and the gas valve turned to the “ON” position. Ensure
21W415-0614 / A / 07.24.075. FAN SPEED SETTINGThis function controls the speed of the hot air circulating fan. To change the fan speed, use the UP an
22W415-0614 / A / 07.24.07ADDRESS SETTING PROCEDUREUse the UP and DOWN key on the transmitter until the cursor (small triangle) is left of the clock i
23W415-0614 / A / 07.24.07DIP SWITCH NUMBER (0 = ON / 1 = OFF)
24W415-0614 / A / 07.24.07A. This fi replace is equipped with a pilot which must be lit by hand while following these instructions exactly.B. Befo
25W415-0614 / A / 07.24.07ADJUSTMENTSTURN OFF THE GAS AND ELECTRICAL POWER BEFORE SERVICING THE FIREPLACE.CAUTION: Label all wires prior to disconnect
26W415-0614 / A / 07.24.07PILOT BURNERTHERMOCOUPLETHERMOPILEFLAME MUST ENVELOP UPPER 3/8” TO 1/2” OF THERMOCOUPLE & THERMOPILE Closing the air
27W415-0614 / A / 07.24.07# PART NO. DESCRIPTION 1* W390-0002 DOOR LATCH (EA)2 W725-0047 NATURAL GAS VALVE - MODULATING 2 W725-0048 PROPANE GAS
28W415-0614 / A / 07.24.07648754022272829303426253361326131116220214151231318166852552176436667AUXON0:0000ON/OFFFEATURE SELECT* WARNING: This is a fa
29W415-0614 / A / 07.24.07White / grey film forms.Sulphur from fuel is being deposited on glass, logs or combustion chamber sur-faces.- clean the gla
3W415-0614 / A / 07.24.07ALL SPECIFICATIONS AND DESIGNS ARE SUBJECT TO CHANGE WITHOUT PRIOR NOTICE DUE TO ON-GOING PRODUCT IMPROVEMENTS. NAPOLEON®® IS
30W415-0614 / A / 07.24.07Main burner goes out; pilot goes out.Main burner goes out; pilot stays on.Pilot fl ame is not large enough or not engulfi ng t
31W415-0614 / A / 07.24.07Fireplace Service HistoryThis fireplace must be serviced annually depending on usageDATEDEALER NAMESERVICE TECHNICIAN NAMESE
32W415-0614 / A / 07.24.07NO TES
4W415-0614 / A / 07.24.076"Provide adequate ventilation and combustion air. Provide adequate accessibility clearance for servicing and operat-ing
5W415-0614 / A / 07.24.07We Suggest that our gas hearth products be installed and serviced by profession-als who are certified in the U.S. by the Nati
6W415-0614 / A / 07.24.07Simple venting confi guration (only one 90° elbow)VERTICAL RISE IN FEETVTFIGURE 4See graph to determine the required vertical
7W415-0614 / A / 07.24.07H2H1V190°See graph to determine the required vertical rise VT for the required horizontal run HT.V1 = VT = 6 ft H1 = 3 f
8W415-0614 / A / 07.24.07MAXIMUM VERTICAL RISE IN FEETVT HORIZONTAL VENT RUN PLUS OFFSET IN FEET HTThe shaded area within the lines represents accepta
9W415-0614 / A / 07.24.07AIR TERMINAL INSTALLATIONS***** Recommended to prevent condensation on windows and thermal breakage********** It is recommend
Comments to this Manuals