Napoleon-fireplaces GDIZC-P User Manual download pdf (Page 6)

W415-0223 / D / 01.12.04

Move the insert close to its final position inside the wood-

burning fireplace. This unit is equipped with 6 levelling

screws located as follows: two are on either side of the

circulation blower on the rear panel; four are located front

and back on either side beneath the log support. Level

using four of the levelling screws. See Figure 1a. Levelling

the unit will eliminate rocking or excessive noise when the

fan is in operation. Once the unit is level, move it partially

into place within the fireplace to allow for all connections to

be made. It is not practical to level the insert once the it has

been installed. Determine the required depth prior to in-

stalling the unit and adjust the four levelling screws accord-

ingly.

Chimney installation must conform to both national and

local code requirements. The chimney must be lined with

one 2" or 3" diameter liner for intake and one 3" diameter

liner for exhaust. The minimum and maximum vent lengths

are 10 and 35 feet respectively. Recommended Napoleon

kits come in 3 lengths: While the liners must be continuous

from the fireplace to the terminal, to achieve the needed

length, they may be coupled, using an aluminium coupler,

provided installation is sealed & secured.

We recommend that exhaust vents that pass through

unheated spaces, such as a garage or attic, be

wrapped in a protective sleeve to minimize condensa-

tion and reverse flow symptoms. See Trouble Shooting

for details.

This unit is approved for use with a 2" liner for air intake

and a 3" liner for exhaust. For best performance,

however, it is recommended to use two 3" liners.

If a 2" liner is used for the intake, it is necessary to

adjust the primary air shutter. See "Air Shutter Settings"

on page 11.

1. OUTSIDE: Slip one

end of a liner a minimum

of 2" over one of the

collars of the terminal. Se-

cure using 3 screws. Then

seal the joint and screw

heads with high tempera-

ture sealant. Repeat with

the other liner.

NOTE: We recommend that the other end of the exhaust

liner be marked to eliminate the exhaust liner being con-

nected to the intake collar at the unit.

FIGURE 3

4. Detach the two screws from the back of the firebox and

remove the panel, as illustrated.

5. Reaching in through the insert, manoeuvre the vent con-

nection assembly through the openings in the firebox top,

taking care not to damage the gasket. In case of a low

ceiling fireplace, the extension should be removed and

reinstalled after the vent connection is secured to the fire-

box. Attach the restrictor plate to the centre stud and se-

cure the assembly using the three studs and ¼-20 hex

nuts.

INSERT VENT CONNECTION

CHIMNEY CONNECTION

FIGURE 4

VENT CONNECTOR

EXTENSION

RESTRICTOR

PLATE

STUDS

FIGURE5a-b

1-2" & 1-3" DOUBLE PLY ALUMINUM LINER-INLET AND EXHAUST &

2-3" TO 2" REDUCER:

GDI-2320KT VENT KIT 20FT

GDI-2325KT VENT KIT 25FT

GDI-2335KT VENT KIT 35FT

2-3" DOUBLE PLY ALUMINUM LINER-INLET AND EXHAUST:

GDI-320KT VENT KIT 20FT

GDI-325KT VENT KIT 25 FT

GDI-335KT VENT KIT 35 FT

2. Gently stretch the liners to the required lengths and in-

sert into the chimney. Place the terminal onto the top of the

chimney cap and fit the flashing plate to suit. Make weather

tight by sealing with caulking (not supplied) and fasten to

the chimney with screws and plugs (not supplied)

3. INSIDE: Attach and secure the flex liners to the vent

connection assembly using the same procedure as be-

fore, ensuring that the marked exhaust liner is attached

to the exhaust collar.

FIGURE 2

1 2 3 4 5 6 7 8 9 10 11 ... 15 16

Comments to this Manuals

No comments

Napoleon-fireplaces GDIZC-P User Manual Page 6

Comments to this Manuals

Related products and manuals for Kiln Napoleon-fireplaces GDIZC-P