Napoleon-fireplaces GDIZC-P User Manual download pdf (Page 9)

W415-0223 / D / 01.12.04

The on-off switch is located behind the left side control

door.

Purge all gas lines with the glass door open. Assure

that a continuous gas flow is at the burner before clos-

ing the door. Allow several minutes (5-15) for the flame

to stabilize after ignition.

Do not operate the main burner of the in-

sert with the door removed.

When lit for the first time, the fireplace will emit a slight

odour for a few hours. This is a normal temporary con-

dition caused by the "burn-in" of paints and lubricants

used in the manufacturing process and will not occur

again. Simply open a window to sufficiently ventilate

the room. After extended periods of non-operation such

as following a vacation or a warm weather season, the

fireplace may emit a slight odour for a few hours. This is

caused by dust particles in the heat exchanger burning

off. Open a window to sufficiently ventilate the room.

PURGE THE GAS LINE WITH THE GLASS DOOR OPEN.

7. Turn gas knob counter-clockwise

to pilot.

8. Depress slightly and hold gas knob while lighting the pilot

with the push button ignitor. Keep knob depressed for one

minute, then release. If pilot does not continue to burn, re-

peat steps 3 through 7.

9. With pilot lit, depress and turn gas knob counter-clock-

wise to on.

10. If equipped with flame adjustment valve, push and turn

knob to high.

11. If equipped with remote on-off switch/thermostat, main

burner may not come on when you turn valve to on. Remote

switch must be in the on position to ignite burner.

12. Turn on all electric power to the fireplace.

FLAME ADJUSTMENT

KNOB

ON/OFF KNOB

A. This fireplace is equipped with a pilot which must be lit

by hand. While following these instructions exactly.

B. Before operating smell all around the fireplace area for

gas and next to the floor because some gas is heavier

than air and will settle on the floor.

C. Use only your hand to turn the gas control knob. Never

use tools. If the knob will not turn by hand, do not try to

repair it. Call a qualified service technician. Force or at-

tempted repair may result in a fire or explosion.

D. Do not use this fireplace if any part has been under water.

Immediately call a qualified service technician to inspect

the fireplace and replace any part of the control system

and any gas control which has been under water.

• Turn off all gas to the fireplace.

• Open windows.

• Do not try to light any appliance.

• Do not touch any electric switch; do not use any phone in

your building.

• Immediately call your gas supplier from a neighbour's

phone. Follow the gas supplier's instructions.

• If you cannot reach your gas supplier, call the fire depart-

ment.

When lighting and re-lighting, the gas knob cannot be turned

from pilot to off unless the knob is depressed slightly.

1. Stop! Read the above safety information on this label.

2. Turn off all electric power to the fireplace.

3. Turn the gas knob clockwise

to off.

4. Wait five (5) minutes to clear out any gas. If you smell gas

including near the floor. Stop! Follow "B" in the above safety

information on this label. If you don't smell gas go the next step.

5. If fireplace is equipped with flame adjustment valve turn

clockwise to off.

6. Find pilot located in front of back log.

2. Push in gas control knob slightly and turn clockwise

to off. Do not force.

1. Turn off all electrical power to the unit if service is to be

performed.

TURN OFF THE GTURN OFF THE G

TURN OFF THE G

AS AND UNPLAS AND UNPL

AS AND UNPL

UG ELECTRICAL POUG ELECTRICAL PO

UG ELECTRICAL PO

WERWER

WER

BEFORE SERBEFORE SER

BEFORE SER

VICING THE FIREPLVICING THE FIREPL

VICING THE FIREPL

CE INSERCE INSER

CE INSER

T!T!

CAUTION: Label all wires prior to disconnection when serv-

icing controls. Wiring errors can cause improper and dan-

gerous operation. Verify proper operation after servicing.

This insert and its venting system should be inspected

before use and at least annually by a qualified service per-

son. The fireplace area must be kept clear and free of

combustible materials, gasoline or other flammable va-

pours and liquids. The flow of combustion and ventilation

air must not be obstructed.

1. In order to properly clean the burner and pilot assembly,

remove the logs exposing both assemblies.

2. Keep the control compartment, logs, burner, air shutter open-

ing and the area surrounding the logs clean by vacuuming

or brushing, at least once a year.

3. Check to see that all burner ports are burning. Clean out

any of the ports which may not be burning or are not burning

properly.

4. Check to see that the pilot flame is large enough to engulf

the thermocouple on one leg and reaches toward the burner

on the other leg.

5. Replace the cleaned logs.

6. Check to see that the main burner ignites completely on all

openings when the gas knob for the burner is turned on. A

5-10 second total light-up period is satisfactory. If ignition

takes longer, consult your Napoleon dealer/distributor.

7. Check that the door gasketing is not broken or missing.

Replace if necessary.

OPERATION / MAINTENANCE

WHAT TO DO IF YOU SMELL GAS:

OPERATING INSTRUCTIONS

FOR YOUR SAFETY READ BEFORE LIGHTING:

LIGHTING INSTRUCTIONS

TO TURN OFF GAS

MAINTENANCE

FIGURE 19

FIGURE 20

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

Comments to this Manuals

No comments

Napoleon-fireplaces GDIZC-P User Manual Page 9

Comments to this Manuals

Related products and manuals for Kiln Napoleon-fireplaces GDIZC-P